Simply Sony [Sony TC-FX25]

Today's special is a Sony TC-FX25 stereo cassette deck with no tape movement. The belts were all intact but had sat unused for so long that they had set into oval crispy things, so that was the first port of call.

This is a very straightforward deck - single playing direction, logic controls, manual selection of tape type and Dolby, LED bar graph recording level indicators and those horrid slide pots which were so popular at the time. You need to take off the top case (just a few obvious screws) and the bottom plate, which is held by three screws along the back edge and hooks under the front panel. The tape carrier door slides up and off with the door open. The front panel is clipped into place and just comes off forwards, and you have to disconnect a couple of plugs on the main circuit board to free it by threading the wiring loom out through the chassis. You can re-connect them directly to the PCB and the machine can still be operated, but note that on this old model, the mains transformer is fully exposed with tags carrying mains voltage on the top - I made up a cardboard box to cover the terminals while I was working on it.

To remove the transport mechanism there are four front-facing screws around its edge - coloured dark to distinguish them from any others. I needed to undo a few cable ties before the deck could be taken out, then disconnected some plugs on the main PCB - there are several similar but they are all different numbers of ways, so although I did make a map first, it's difficult to go wrong anyway. I guess it might help any viewer if I were to put in a scan of things like scribble maps, but I'm pushed for time at the moment. If anyone wants more info just stick a comment in.

The back plate with motor comes off easily allowing access to the first two of the four belts in this model. Again, without access to the exact replacement parts you have to do a bit of substitution. I found that the capstan belt was flat section, and CPC Farnell had a suitable one in their AVBELT5 (71mm dia. by 2.8mm wide, 0.5mm thick). The fast-forward belt driving the spools is replaced by an AVBELT76 (37mm dia. by 1.2mm square section). Then the back plate can be re-fitted.

The other two belts are accessed by removing the front plate and tape carrier assembly. This involves taking out a couple of brass screws each side which pivot the stays and I seem to recall there were a couple more at the top or side fixing the plate to the deck frame - but it was all pretty obvious. Once the screws are out, the assembly falls out forwards. It's probably worth keeping it in about the same position as it comes out, to save getting in a 'folding deckchair' pickle when re-fitting. At this point I was able to fit the other two belts - AVBELT69 (32mm dia. by 1.2mm square section) driving the take-up spool carrier, and the tape counter belt AVBELT100 (64mm dia. by 1.2mm square section) from the take-up spool spindle to the counter. As the tape counter is mechanical and still mounted on the main chassis, I left the drive belt loose having threaded it through the metalwork and then I re-fitted the front plate and tape carrier assembly. Throughout all this I made sure that I cleaned and lubricated the heads, pinch wheels and bearings as usual.

After putting it all back together, the tape mechanism worked perfectly with no slipping or wobble. Unfortunately there was only one channel playing and touching the PCB or wiring caused much crackling. Eventually I traced the problem to the tape head connectors - there seemed to be no dry solder joints so I used contact cleaner (Electrolube) on all the connectors, making sure to work them off and on to scrape off any tarnish. This sorted it out and the whole machine is now performing well.

This machine was hi-fi for its day but certainly not anything special, and even fully working it can't outperform any decent bit of kit - it's very basic. Added to that, it's not pristine - one or two rusty scratches - and uses cassettes which are hardly the medium of the future any more. But it has two standard (quarter inch) microphone inputs on the front and is still good for basic recording or transcribing old tapes, so maybe it will find a use somewhere. Anyway, it's satisfying to see it back in working order.